Monday, 8 April 2013

Anna university EE2203 Electronic Devices and Circuits April/May 2010 previous year Question Paper

B.E./B.Tech. DEGREE EXAMINATION, APRIL/MAY 2010
Third Semester
Electrical and Electronics Engineering
EE2203 — ELECTRONIC DEVICES AND CIRCUITS
(Regulation 2008)


  PART A — (10 × 2 = 20 Marks)

1. What is meant by diffusion current in a semi conductor?
2. A silicon diode has a saturation current of 7.5μ A at room temperature 300°K.
Calculate the saturation current at 400°K.
3. Draw the input and output characteristics of a transistor in CE configuration
and mark the cutoff, saturation and active regions.
4. State the advantages of optocoupler. (Write any four).
5. Compare JFET with BJT.
6. Define amplification factor in JFET.
7. Define CMRR and write its significance in differential amplifiers.
8. List the advantages of negative feedback amplifiers.
9. Sketch the idealized characteristics for the filter types.
(a) Low pass
(b) High pass
(c) Band pass
(d) Band reject filters.
10. Define intrinsic stand off ratio of UJT and draw its equivalent circuit.


PART B — (5 × 16 = 80 Marks)

11. (a) With a neat diagram explain the working of a PN junction diode in forward bias and
reverse bias and show the effect of temperature on its V-I characteristics. (16)
Or
(b) (i) Explain V-I characteristics of Zener diode. (8)
(ii) Draw the circuit diagram and explain the working of full wave bridge rectifier and derive
the expression for average output current and rectification efficiency. (8)

12. (a) (i) Draw the h-parameter equivalent circuit of a transistor in CE configuration. (8)
(ii) Describe the methods of determination of h-parameters from its static Input and output
characteristics. (8)
Or
(b) (i) Explain the important characteristics of optocoupler. (6)
(ii) Explain the switching characteristics of transistor with neat sketch. (10)

13. (a) (i) Explain how the transconductance of a JFET varies with drain current and gate
voltage characteristics and transfer characteristics. (12)
(ii) A JFET has the following parameters IDDS = 32 mA, VGS(off) = -8 Volts, VGS = -4.5
Volts. Find the values of drain current. (4)
Or
(b) (i) Explain the working of n-channel enhancement type MOSFET.
Sketch its typical characteristics. (10)
(ii) Explain the application of FET as a voltage variable resistor. (6)

14. (a) (i) Draw the block diagram of a voltage series feedback amplifier and derive the
equation for input impedance, output impedance and the voltage gain. (10)
(ii) Calculate the voltage gain, input and output resistances of a voltage series feedback
amplifier having AV = 300, Ri = 1.5 k, Ro = 50 k and β = 1/15. (6)
Or
(b) (i) Differentiate oscillator with amplifier. (4)
(ii) Draw the circuit of a Hartley oscillator and derive the condition for the frequency of
oscillation. (12)

15. (a) (i) Describe the operation of UJT and its emitter characteristics. (8)
(ii) Describe the working of a Schmitt trigger circuit with the help of necessary waveforms.
(8)
Or
(b) (i) Sketch the response of RC high pass filter for the following inputs and explain.
(1) Ramp
(2) Pulse. (8)
(ii) Explain the operation of a bistable multi-vibrator circuit with neat sketch. (8)

----------------------------------------------------------------------------------------------------------------
EE2203 — ELECTRONIC DEVICES AND CIRCUITS QUESTION PAPER 

Thursday, 4 April 2013

EE2302 Electrical Machines II Nov/Dec 2011 question Paper | Anna university Electrical Machines II previous year question papers

B.E. DEGREE EXAMINATION, NOVEMBER/DECEMBER 2011.
Fifth Semester
Electrical and Electronics Engineering
EE 2302 — ELECTRICAL MACHINES — II
(Regulation 2008)

PART A — (10 × 2 = 20 marks)

1. What do you mean by single layer and double layer winding?
2. What are the various function of damper winding provided with alternator?
3. What is a synchronous capacitor?
4. What are V–curves?
5. Why are the rotor slots of a 3 phase induction motors skewed?
6. Define slip of induction motor.
7. State the effect of rotor resistance on starting torque.
8. What are the various method of speed control of 3 phase induction motor?
9. What type of motor is used for ceiling fan?
10. State the application of shaded pole motor.


PART B — (5 × 16 = 80 marks)

11. (a) (i) Derive from first principle, the EMF of 3 phase alternator. (8)
(ii) The following open circuit and short circuit test are made on a 6000 kVA, 6600 V, star connected, 2 pole, 60 Hz turbine driven alternator. If I = 125 A, at open circuit terminal voltage = 8200 V. With armature short circuited I = 125 A. IL = 800 A (line). At the rated load and upf armature loss is 1.5% of out put. Determine the percentage regulation at rated load and 0.8 p.f. lag. (8)
Or
(b) (i) Explain how will you determine the d and q axis reactance of a synchronous machine in your laboratory. (8)
(ii) For the salient synchronous machine, derive the expression for power developed as a function of load angle. (8)

12. (a) Explain V–curve and inverted V curve. (16)
Or
(b) Explain effect of changing field current excitation at constant load. (16)

13. (a) (i) Explain with neat sketches the principle of a 3 Phase induction motor. (8)
(ii) A 6 pole, 50 Hz, 3-Phase, induction motor running on full load develops a useful torque of 160 N m. When the rotor emf makes 120 complete cycle per minute. Calculate the shaft power input. If the mechanical torque lost in friction and that for core loss is 10 N m, complete.
(1) The copper loss in the rotor windings.
(2) The input the motor.
(3) The efficiency.
The total stator loss in given to be 800 W. (8)
Or
(b) (i) Explain top slip characteristic of 3 phase induction motor. (8)
(ii) Develop the equivalent circuit for a 3 phase induction motor. (8)

14. (a) Describe with a neat sketch, the principle and working of a star delta starter and autotransformer starter of a 3 phase induction motor. (16)
Or
(b) Explain, with a neat sketch, slip power recovery scheme of 3 phase induction motor. (16)

15. (a) Explain with a neat diagram the following types of single phase induction motor.
(i) Split phase induction run motor.
(ii) Capacitor start induction run motor, and also draw the slip torque characteristics. (16)
Or
(b) Describe the constructional features & principle of operation of hysterisis motor and AC Series motor. (16)

Tuesday, 2 April 2013

Anna University Revaluation Results For Nov/dec 2012 | Anna University UG Revaluation Results 2013 | Anna univ Revaluation results 2012-2013


Anna University Revaluation Results Nov/Dec 2012 Anna University Revaluation Results 2013 for UG/PG Have Been Announced


Grade System -->View Revaluation Results


Mark System --> View Revaluation Results


Like us on facebook to get the just out updates in Facebook


-------------------------------------------------------------------------------------------------------------------------------------
Incoming Search :
anna university revaluation result  2012
Anna University Revaluation Results 2013
anna university chennai revaluation results 2013
anna university revaluation results nov dec 2012
revaluation results anna university nov/dec 2012
anna university nov dec 2012 revaluation results
Anna University Revaluation Results Nov/Dec 2012
Anna University 5thSemester Revaluation Results 2013
Anna University 7th Semester Revaluation Results 2013
Anna University 3rd Semester Revaluation Results 2013
anna university chennai revaluation results nov dec 2012
Anna University Revaluation Results Nov Dec 2012 for UG
Anna University coimbatore, Trichy, Madurai, Tirunelveli Chennai Revaluation Results 2013

Sunday, 31 March 2013

How to calculate cutoff marks for anna university Engineering Counselling

StudentsBlog100

What is cutoff mark?
Cutoff mark is a mark which will be calculated based on the three main subjects that you have written in your 12th Public Board Exam Maths, Physics & Chemistry


What is the use of Cutoff mark??
The main use of the cutoff mark in TNEA 2013 engineering counseling is that this mark is one of the criteria which will be used to calculate Random numbers and they will assign random numbers to each and every student who applied for the counseling. To know what is random number Just CLICK HERE: RANDOM NUMBER

How to calculate cutoff marks??
Cutoff marks will be calculated by three main subjects which you have written in the 12th examinations
First Subject is Maths
Second Subject is Physics
Third Subject is Chemistry

Procedure for calculating cutoff marks:
Divide your Mathematics  mark with 2     = 1st Answer
Divide your Physics          mark with 4     = 2nd Answer
Divide your Chemistry      mark with 4      = 3rd Answer   

Adding 1st Answer + 2nd Answer + 3rd Answer = YOUR CUTOFF MARK

Example for Cut-Off mark Caclulation


SL.NOSUBJECTSMARKSCALCULATIONCUTOFF MARKS
1MATHEMATICS196196 / 298
2Physics179179 / 444.75
3CHEMISTRY183183 / 445.75

Online Cut-Off mark Calculator ---> CLICK HERE


To know details about TNEA 2013 --> CLICK HERE