Showing posts with label Mech Syllabus. Show all posts
Showing posts with label Mech Syllabus. Show all posts

Monday, 25 March 2013

GE 131 - ENGINEERING MECHANICS ANNA UNIVERSITY PREVIOUS YEAR QUESTION PAPER DOWNLOAD

GE 131 - ENGINEERING MECHANICS

PART – A (10 X 2 = 20 Marks)

1. Determine the resultant of the three forces F1 = 2.0i + 3.3j – 2.6k; F2 = - i + 5.2j – 2.9k; and F3 = 8.3i – 6.6j + 5.8k, which are concurrent at the point (2, 2, -5.). The forces are in newtons and the distances are in metres.

2. A force F = (6N)i – (3Nj – (4N)k is acting at a point P whose position vector from the origin 'O' of the coordinate axes is (8 mm)i + (6 mm)j – (4 mm)k. Find the moment of the force about the origin.
3. State Varignon's theorem.
4. State the theorems of Pappus and Guldinus to find out the surface area and the volume of a body.
5. State the Coulomb's laws of dry friction.
6. A belt embraces an angle of 200? over the surface of a pulley of 500 mm diameter. If the tight side tension of the belt is 2.5 kN. Find out the slack side tension of the belt. The coefficient of friction between the belt and the pulley can be taken as 0.3.
7. The motion of a particle in defined by the relation x = t3 – 15 t2 – 20, where 'x' is expressed in metres and 't' in seconds. Determine the acceleration of the particle at t = 3 seconds.
8. A mass of 50 kg. has an initial velocity of 15 m/s. horizontally on a smooth surface. Determine the value of horizontal force that will bring the mass to rest in 4 seconds.
9. Define the term 'coefficient of restitution' of two bodies under impact.
10. State the principle of conservation of linear momentum of a particle.

PART – B (5 x 16 = 80 Marks)

11. A force F acts at the origin of a coordinate system in a direction defined by the angles ?x = 69.3? and ?z = 57.9?. If the component of the force F along y direction is = -174N, determine.
(i) the angle ?y (4 Marks) (ii) the magnitude of the force F (4 Marks) (iii) the components of the force F along x and z directions. (4 Marks) (iv) the component of the force F on a line through the origin (4 Marks) . and the point (1,1,1).
12. (a) A load P of 3500 N is acting on the boom, which is held by a cable BC as shown in Fig.12(a). The weight of the boom can be neglected.
(i) Draw the free body diagram of the boom. (4 Marks) (ii) Find out the tension in cable BC. (8 Marks) (iii) Determine the reaction at A. (4 Marks)
(OR)
(b) Three forces +20N, -10N and +30N are acting perpendicular to x z plane as shown in Fig. Q.12(b). The lines of action of all the forces are parallel to y-axis. The coordinates of the point of action of these forces along x and z directions are respectively (2,3), (4,2) and (7,4), all the distances being referred in metres. Find out.
(i) The magnitude of the resultant force. (4 Marks) (ii) The location of the resultant. (12 Marks)
13.(a) (i) Determine the coordinates of the centroid of the shaded area shown in Fig. Q.13 (a) if the area removed is semicircular. (4 Marks) (ii) Find the moment of inertia of the shaded area about the centroidal axes, the axes being parallel to x and y-axes. (6 Marks) (iii) Find the product of inertia of the shaded area about the centroidal axes. . (6 Marks)
(OR)
(b) Find the mass moment of inertia of the rectangular block shown in Fig. Q.13(b), about the x and y axes. A cuboid of 20 mm x 20 mm x 20 mm has been removed from the rectangular block as shown in the figure. The mass density of the material of the block is 7850 kg/m3.

14.(a) Two masses m1 and m2 are tied together by a rope parallel to the inclined plane surface, as shown in Fig. Q.14(a). Their masses are 22.5 kg. and 14 kg. respectively. The coefficient of friction between m1 and the plane is 0.25, while that of mass m2 and the plane is 0.5. Determine.
(i) the value of the inclination of the plane surface, ?, for which the masses will just start sliding. (6 Marks) (ii) the tension in the rope. (6 Marks) (iii) what will be the friction forces at the mass surfaces. (4 Marks)
(OR)
(b) The driver of an automobile decreases the speed at a constant rate from 72 to 48 km./hour over a distance of 230 m. along a curve of 460 m. radius. Determine the magnitude of the total acceleration of the automobile, after the automobile, after the automobile has traveled 150 m. along the curve.
15.(a) Two steel blocks, shown in Fig. Q. 15(a), slide without friction on a horizontal surface. The velocities of the blocks immediately before impact are as shown. If the coefficient of restitution between the blocks is 0.75, determine (i) the velocities of the blocks after impact and (12 Marks) (ii) the energy loss during impact. (4 Marks)
(OR)
(b) A plate shown in Fig.Q.15 (b) moves in the xy plane as below.
x component velocity of point A = 450 mm/s. x component velocity of point B = -150 mm/s. y component velocity of point C = -900 mm/s. Determine : (i) the angular velocity of the plate and (8 Marks) . (ii) the velocity of the point B. (8 Marks)

Friday, 28 December 2012

GE2151 BASIC ELECTRICAL AND ELECTRONICS ENGINEERING SYLLABUS | ANNA UNIVERSITY SECOND SEMESTER SYLLABUS

(Common to branches under Civil, Mechanical and Technology faculty)

UNIT I ELECTRICAL CIRCUITS & MEASURMENTS
Ohm’s Law – Kirchoff’s Laws – Steady State Solution of DC Circuits – Introduction to AC Circuits –
Waveforms and RMS Value – Power and Power factor – Single Phase and Three Phase Balanced
Circuits.
Operating Principles of Moving Coil and Moving Iron Instruments (Ammeters and Voltmeters),
Dynamometer type Watt meters and Energy meters.

UNIT II ELECTRICAL MECHANICS 
Construction, Principle of Operation, Basic Equations and Applications of DC Generators, DC
Motors, Single Phase Transformer, single phase induction Motor.

UNIT III SEMICONDUCTOR DEVICES AND APPLICATIONS
Characteristics of PN Junction Diode – Zener Effect – Zener Diode and its Characteristics – Half
wave and Full wave Rectifiers – Voltage Regulation.
Bipolar Junction Transistor – CB, CE, CC Configurations and Characteristics – Elementary
Treatment of Small Signal Amplifier.

UNIT IV DIGITAL ELECTRONICS
Binary Number System – Logic Gates – Boolean Algebra – Half and Full Adders – Flip-Flops –
Registers and Counters – A/D and D/A Conversion (single concepts)

UNIT V FUNDAMENTALS OF COMMUNICATION ENGINEERING
Types of Signals: Analog and Digital Signals – Modulation and Demodulation: Principles of
Amplitude and Frequency Modulations. Communication Systems: Radio, TV, Fax, Microwave, Satellite and Optical Fibre (Block Diagram
Approach only).

TOTAL : 60 PERIODS

TEXT BOOKS:
1. N. Mittle “Basic Electrical Engineering”,Tata McGraw Hill Edition, New Delhi, 1990.
2. R.S. Sedha, “Applied Electronics” S. Chand & Co., 2006.
REFERENCES:
1. Muthusubramanian R, Salivahanan S and Muraleedharan K A, “Basic Electrical, Electronics and
Computer Engineering”,Tata McGraw Hill, Second Edition, (2006).
2. Nagsarkar T K and Sukhija M S, “Basics of Electrical Engineering”, Oxford press (2005).
3. Mehta V K, “Principles of Electronics”, S.Chand & Company Ltd, (1994).
4. Mahmood Nahvi and Joseph A. Edminister, “Electric Circuits”, Schaum’ Outline Series, McGraw
Hill, (2002).
5. Premkumar N, “Basic Electrical Engineering”, Anuradha Publishers, (2003).

ME2151 ENGINEERING MECHANICS SYLLABUS | ANNA UNIVERSITY SECOND SEMESTER SYLLABUS

UNIT I BASICS & STATICS OF PARTICLES
Introduction – Units and Dimensions – Laws of Mechanics – Lame’s theorem, Parallelogram and
triangular Law of forces – Vectors – Vectorial representation of forces and moments – Vector
operations: additions, subtraction, dot product, cross product – Coplanar Forces – Resolution and
Composition of forces – Equilibrium of a particle – Forces in space – Equilibrium of a particle in
space – Equivalent systems of forces – Principle of transmissibility – Single equivalent force.

UNIT II EQUILIBRIUM OF RIGID BODIES
Free body diagram – Types of supports and their reactions – requirements of stable equilibrium –
Moments and Couples – Moment of a force about a point and about an axis – Vectorial
representation of moments and couples – Scalar components of a moment – Varignon’s theorem –
Equilibrium of Rigid bodies in two dimensions – Equilibrium of Rigid bodies in three dimensions

UNIT III PROPERTIES OF SURFACES AND SOLIDS
Determination of Areas and Volumes – First moment of area and the Centroid of sections –
Rectangle, circle, triangle from integration – T section, I section, - Angle section, Hollow section by
using standard formula – second and product moments of plane area – Rectangle, triangle, circle
from integration – T section, I section, Angle section, Hollow section by using standard formula –
Parallel axis theorem and perpendicular axis theorem – Polar moment of inertia – Principal moments
of inertia of plane areas – Principal axes of inertia – Mass moment of inertia – Derivation of mass
moment of inertia for rectangular section, prism, sphere from first principle – Relation to area
moments of inertia.

UNIT IV DYNAMICS OF PARTICLES
Displacements, Velocity and acceleration, their relationship – Relative motion – Curvilinear motion –
Newton’s law – Work Energy Equation of particles – Impulse and Momentum – Impact of elastic
bodies.

UNIT V FRICTION AND ELEMENTS OF RIGID BODY DYNAMICS
Frictional force – Laws of Coloumb friction – simple contact friction – Rolling resistance – Belt
friction.
Translation and Rotation of Rigid Bodies – Velocity and acceleration – General Plane motion.

TOTAL: 60 PERIODS

TEXT BOOK:
1. Beer, F.P and Johnson Jr. E.R. “Vector Mechanics for Engineers”, Vol. 1 Statics and Vol. 2
Dynamics, McGraw-Hill International Edition, (1997).

REFERENCES:
1. Rajasekaran, S, Sankarasubramanian, G., “Fundamentals of Engineering Mechanics”, Vikas
Publishing House Pvt. Ltd., (2000).
2. Hibbeller, R.C., “Engineering Mechanics”, Vol. 1 Statics, Vol. 2 Dynamics, Pearson Education
Asia Pvt. Ltd., (2000).
3. Palanichamy, M.S., Nagam, S., “Engineering Mechanics – Statics & Dynamics”, Tata McGraw-
Hill, (2001).
4. Irving H. Shames, “Engineering Mechanics – Statics and Dynamics”, IV Edition – Pearson
Education Asia Pvt. Ltd., (2003).
5. Ashok Gupta, “Interactive Engineering Mechanics – Statics – A Virtual Tutor (CDROM)”, Pearson
Education Asia Pvt., Ltd., (2002).

Monday, 24 December 2012

Anna University Chennai Mech Syllabus (2nd|3rd|4th|5th|6th|7th|8th Semester Syllabus)

ANNA UNIVERSITY, CHENNAI
REGULATIONS 2008
B.E. / B.TECH. DEGREE OFFERED IN
THE AFFILIATED INSTITUTIONS OF ANNA UNIVERSITY
II TO VIII SEMESTERS CURRICULUM AND SYLLABI

To Download the Syllabus : Click Here